Knowledge Resource Center for Ecological Environment in Arid Area
DOI | 10.1080/10584587.2020.1728818 |
Research on Factors Affecting Cutting Resistance of Cutting Blade Based on Sand Trough Test | |
Wang, Mengmeng; Liu, Jinhao; Wang, Dian; Wu, Jian | |
通讯作者 | Liu, JH (corresponding author), Beijing Forestry Univ, Sch Engn, Beijing, Peoples R China. |
来源期刊 | INTEGRATED FERROELECTRICS
![]() |
ISSN | 1058-4587 |
EISSN | 1607-8489 |
出版年 | 2021 |
卷号 | 221期号:1页码:20-32 |
英文摘要 | The use of sand fixing equipment to lay straw checkerboard barrier has become the main means of desert control, while the design of laying system for sand fixing equipment lacks relevant theoretical guidance. The factors that influence the cutting resistance are complex in the process of laying straw checkerboard barrier. A sand trough test-bed was designed to study the factors affecting the cutting resistance in the blade cutting process. The structure of the test platform was composed of disc knife, sand tank, bracket, lifting slide rail device, force measuring device, driving device, etc. By establishing the mathematical model of the working force of the cutter, the diameter of the cutter was determined as 720 mm and the thickness of the cutter was 6 mm. The water content of the tested sand was 6.3%, the wet density was 1.141%, and the dry density was 1.140%. The sand barrier material was selected from the natural dry rice straw, the diameter of the single straw was about 4 similar to 5mm, the length of the straw was about 700 mm, and the quality of the single rice straw evenly laid 1000 mm was 160 g. The driving device chose the stepping motor as power source, which can drive the lifting slide rail device moving in horizontal direction. The tension pressure sensor of the force measuring device was installed by articulated form, which can obtain test data. The parameters of the speed control system were calculated and the schematic diagram of the drive was designed, and the laying speed could be adjusted by adjusting the frequency of the stepping motor. The influence of the change of inserting depth, laying speed and laying thickness on the insertion resistance of the cutter disc were tested. Inserting depth and laying thickness had significant influence on insertion resistance and traction force. When the thickness of the thickness was 160 g/m and the insertion depth was 150 similar to 210mm, the insertion resistance was around 1700 similar to 2450 N, and the traction value was between the 550 similar to 1200 N. When laying thickness reached 480 g/m, the insertion resistance reached about 3200 N, traction was up to 1600 N. According to the orthogonal test results, the best combination was insertion depth of 210 mm, laying speed of 0.056 similar to 0.112m/s, and laying thickness of 480 g/m. The order of the main and secondary factors affecting the test results was the maximum insertion depth, the laying thickness and the minimum laying speed. A regression model between insertion resistance, traction force and insertion depth and thickness was established, and relevant experiments are carried out to verify the rationality of the model. It was found that the laying speed had little effect on the test results. The laying thickness had a more significant impact on insertion resistance, while insertion depth had a more significant impact on traction force according to the surface of double parameters. The experimental results provided a theoretical basis for the design of the laying and the traction power system of sand fixing equipment. |
英文关键词 | Straw checkerboard barrier sand trough test orthogonal test cutting resistance |
类型 | Article |
语种 | 英语 |
收录类别 | SCI-E |
WOS记录号 | WOS:000730086800001 |
WOS类目 | Engineering, Electrical & Electronic ; Physics, Applied ; Physics, Condensed Matter |
WOS研究方向 | Engineering ; Physics |
资源类型 | 期刊论文 |
条目标识符 | http://119.78.100.177/qdio/handle/2XILL650/373872 |
作者单位 | [Wang, Mengmeng; Liu, Jinhao; Wang, Dian; Wu, Jian] Beijing Forestry Univ, Sch Engn, Beijing, Peoples R China |
推荐引用方式 GB/T 7714 | Wang, Mengmeng,Liu, Jinhao,Wang, Dian,et al. Research on Factors Affecting Cutting Resistance of Cutting Blade Based on Sand Trough Test[J],2021,221(1):20-32. |
APA | Wang, Mengmeng,Liu, Jinhao,Wang, Dian,&Wu, Jian.(2021).Research on Factors Affecting Cutting Resistance of Cutting Blade Based on Sand Trough Test.INTEGRATED FERROELECTRICS,221(1),20-32. |
MLA | Wang, Mengmeng,et al."Research on Factors Affecting Cutting Resistance of Cutting Blade Based on Sand Trough Test".INTEGRATED FERROELECTRICS 221.1(2021):20-32. |
条目包含的文件 | 条目无相关文件。 |
除非特别说明,本系统中所有内容都受版权保护,并保留所有权利。