Knowledge Resource Center for Ecological Environment in Arid Area
| On the running-in of gears | |
| Sjöberg;Sören | |
| 出版年 | 2010 |
| 学位授予单位 | KTH, Machine Elements, Stockholm : KTH |
| 英文摘要 | The general trend in gear industry, today, is an increased focus on gear transmission efficiency. Gear transmission efficiency losses arise from loaded and unloaded gear contacts, seals, lubricant and bearings. One way of minimising the losses is to lower the lubricant viscosity. This will reduce the speed dependent losses. However, the load dependent losses might increase. To avoid this, the ratio between lubricant film thickness and surface roughness must be maintained, which can be fulfilled by producing smoother gear surfaces. As a starting point for this realisation process, the present manufacturing processes, the design tools and the characteristics of the gear flank interface must be further investigated and developed. This must be achieved with an emphasis on economic production. This thesis focuses on our understanding of how different gear manufacturing methods —particularly the contribution of the running-in process—affect the surface characteristics, with the view of increasing gearbox efficiency. The thesis consists of a summary and three appended papers. Paper A and paper B discuss the relationship between design parameters and real gear wheel surfaces manufactured with different manufacturing methods. The research hypothesis was that the contact area ratio is a descriptive parameter for the contact condition. Paper A deals with the influence of manufacturing method on the initial contact conditions and also serves as a validation of the simulation program used. The emphasis in Paper B is the changes that occur during running-in, and to correlate these changes to design requirements. Paper C approaches the influences of manganese phosphate-coating and lubricants with respect to friction and the risk of scuffing at the initial contact. The main conclusions of this thesis are that the contact area ratio presents a descriptive measure of how surface topography influences the contact, seen at both a global (form deviation) and local (roughness) level. The surface topography caused by the manufacturing method has a significant influence on the contact area ratio. This is an important result, since neither national standards nor commercially available gear evaluation programs handle surface topography on the local scale. Shaving was found to have the highest contact area ratio, and should therefore be the best choice if deviations from case hardening could be minimised. It is also confirmed that gear-like surfaces coated with manganese phosphate have a low coefficient of friction, and raise the limiting load for scuffing failure enormously compared to the ground equivalent. QC 20100518 KUGG Sustainable gear transmission realization |
| 英文关键词 | Gears Gear manufacturing Running-in Surface topography Contact area ratio Manganese phosphate Mechanical engineering Maskinteknik |
| 语种 | 英语 |
| URL | http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-12750 |
| 来源机构 | KTH Royal Institute of Technology |
| 资源类型 | 学位论文 |
| 条目标识符 | http://119.78.100.177/qdio/handle/2XILL650/244844 |
| 推荐引用方式 GB/T 7714 | Sjöberg;Sören. On the running-in of gears[D]. KTH, Machine Elements, Stockholm : KTH,2010. |
| 条目包含的文件 | 条目无相关文件。 | |||||
| 个性服务 |
| 推荐该条目 |
| 保存到收藏夹 |
| 导出为Endnote文件 |
| 谷歌学术 |
| 谷歌学术中相似的文章 |
| [Sjöberg;Sören]的文章 |
| 百度学术 |
| 百度学术中相似的文章 |
| [Sjöberg;Sören]的文章 |
| 必应学术 |
| 必应学术中相似的文章 |
| [Sjöberg;Sören]的文章 |
| 相关权益政策 |
| 暂无数据 |
| 收藏/分享 |
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。
